4G/generate/include/Qspi_Ip_Features.h

/*==================================================================================================
*   Project              : RTD AUTOSAR 4.4
*   Platform             : CORTEXM
*   Peripheral           : FTFC_FLS_IP IPV_QSPI
*   Dependencies         : none
*
*   Autosar Version      : 4.4.0
*   Autosar Revision     : ASR_REL_4_4_REV_0000
*   Autosar Conf.Variant :
*   SW Version           : 1.0.0
*   Build Version        : S32K1_RTD_1_0_0_HF01_D2109_ASR_REL_4_4_REV_0000_20210907
*
*   (c) Copyright 2020-2021 NXP Semiconductors
*   All Rights Reserved.
*
*   NXP Confidential. This software is owned or controlled by NXP and may only be
*   used strictly in accordance with the applicable license terms. By expressly
*   accepting such terms or by downloading, installing, activating and/or otherwise
*   using the software, you are agreeing that you have read, and that you agree to
*   comply with and are bound by, such license terms. If you do not agree to be
*   bound by the applicable license terms, then you may not retain, install,
*   activate or otherwise use the software.
==================================================================================================*/

#if !defined(QSPI_IP_FEATURES_H)
#define QSPI_IP_FEATURES_H

/**
*   @file Qspi_Ip_Features.h
*
*   @addtogroup FLS
*   @{
*/

/* implements Qspi_Ip_Features.h_Artifact */

#ifdef __cplusplus
extern "C"{
#endif

/*==================================================================================================
*                                        INCLUDE FILES
* 1) system and project includes
* 2) needed interfaces from external units
* 3) internal and external interfaces from this unit
==================================================================================================*/


/*==================================================================================================
*                              SOURCE FILE VERSION INFORMATION
==================================================================================================*/
#define QSPI_IP_FEATURES_VENDOR_ID_CFG                      43
#define QSPI_IP_FEATURES_AR_RELEASE_MAJOR_VERSION_CFG       4
#define QSPI_IP_FEATURES_AR_RELEASE_MINOR_VERSION_CFG       4
#define QSPI_IP_FEATURES_AR_RELEASE_REVISION_VERSION_CFG    0
#define QSPI_IP_FEATURES_SW_MAJOR_VERSION_CFG               1
#define QSPI_IP_FEATURES_SW_MINOR_VERSION_CFG               0
#define QSPI_IP_FEATURES_SW_PATCH_VERSION_CFG               0


/*==================================================================================================
*                                      DEFINES AND MACROS
==================================================================================================*/

/* QuadSPI module features */

/*! @brief First address of the serial flash device on the AHB bus. */
#define FEATURE_QSPI_AMBA_BASE                        0x68000000U
/*! @brief Size of AHB buffer. */
#define FEATURE_QSPI_AHB_BUF_SIZE                     1024U
/*! @brief Size of Tx FIFO. */
#define FEATURE_QSPI_TX_BUF_SIZE                      128U
/*! @brief Size of Rx FIFO. */
#define FEATURE_QSPI_RX_BUF_SIZE                      128U
/*! @brief Number of LUT registers that make up a LUT sequence */
#define FEATURE_QSPI_LUT_SEQUENCE_SIZE                4U
/*! @brief Minimum delay in CPU cycles between Tx FIFO reset and Tx FIFO push */
#define FEATURE_QSPI_TX_RESET_DELAY                   (0U)
/* Minimum entries of 4 bytes fill needed to allow Tx operation to start */
#define FEATURE_QSPI_TX_MIN_BUF_FILL                  4U

/*! @brief Supports Double Data Rate operation */
#define FEATURE_QSPI_DDR                              1
/*! @brief QSPI side B is available */
#define FEATURE_QSPI_HAS_SIDE_B                       1
/*! @brief Configurable Idle Signal Drive */
#define FEATURE_QSPI_CONFIGURABLE_ISD                 1

/*! @brief Supports addr. config options (column address, word addressable) */
#define FEATURE_QSPI_ADDR_CFG                         1
/*! @brief Supports byte swap */
#define FEATURE_QSPI_BYTES_SWAP_ADDR                  0

/*! @brief Supports center-aligned read strobe */
#define FEATURE_QSPI_CENTER_ALIGNED_READ_STROBE       0
/*! @brief Supports differential clock */
#define FEATURE_QSPI_DIFFERENTIAL_CLOCK               0

/*! @brief Supports internal DQS sampling mode */
#define FEATURE_QSPI_INTERNAL_DQS                     1
/*! @brief Supports loopback sampling mode */
#define FEATURE_QSPI_LOOPBACK                         1
/*! @brief Supports DQS loopback sampling mode */
#define FEATURE_QSPI_LOOPBACK_DQS                     1
/*! @brief Supports external DQS sampling mode */
#define FEATURE_QSPI_EXTERNAL_DQS                     1
/*! @brief Supports DQS_FA_SEL/DQS_FB_SEL field in MCR register for DQS selection */
#define FEATURE_QSPI_SELECT_DQS                       0

/*! @brief Supports Dll feature */
#define FEATURE_QSPI_HAS_DLL                          0
/*! @brief Supports full DLL features (as opposed to bypass mode only) */
#define FEATURE_QSPI_EXTERNAL_DLL_FULL                0
/*! @brief Supports DLL reference counter and DLL resolution*/
#define FEATURE_QSPI_DLL_LOOPCONTROL                  0


/*! @brief AHB base pointers initializer for all QSPI units */
#define QuadSPI_AHB_PTRS    { FEATURE_QSPI_AMBA_BASE }


#ifdef __cplusplus
}
#endif

/** @} */

#endif /* QSPI_IP_FEATURES_H */