/*==================================================================================================
* Project : RTD AUTOSAR 4.4
* Platform : CORTEXM
* Peripheral :
* Dependencies : none
*
* Autosar Version : 4.4.0
* Autosar Revision : ASR_REL_4_4_REV_0000
* Autosar Conf.Variant :
* SW Version : 1.0.0
* Build Version : S32K1_RTD_1_0_0_HF01_D2109_ASR_REL_4_4_REV_0000_20210907
*
* (c) Copyright 2020-2021 NXP Semiconductors
* All Rights Reserved.
*
* NXP Confidential. This software is owned or controlled by NXP and may only be
* used strictly in accordance with the applicable license terms. By expressly
* accepting such terms or by downloading, installing, activating and/or otherwise
* using the software, you are agreeing that you have read, and that you agree to
* comply with and are bound by, such license terms. If you do not agree to be
* bound by the applicable license terms, then you may not retain, install,
* activate or otherwise use the software.
==================================================================================================*/
/**
* @file Power_Ip_Cfg_Defines.h
* @version 1.0.0
*
* @brief AUTOSAR Mcu - Post-Build(PB) configuration file code template.
* @details Code template for Post-Build(PB) configuration file generation.
*
* @addtogroup POWER_DRIVER_CONFIGURATION Power Ip Driver
* @{
*/
#ifndef POWER_IP_CFG_DEFINES_H
#define POWER_IP_CFG_DEFINES_H
#ifdef __cplusplus
extern "C"{
#endif
/*==================================================================================================
INCLUDE FILES
1) system and project includes
2) needed interfaces from external units
3) internal and external interfaces from this unit
==================================================================================================*/
#include "StandardTypes.h"
/*==================================================================================================
SOURCE FILE VERSION INFORMATION
==================================================================================================*/
#define POWER_IP_CFG_DEFINES_VENDOR_ID 43
#define POWER_IP_CFG_DEFINES_AR_RELEASE_MAJOR_VERSION 4
#define POWER_IP_CFG_DEFINES_AR_RELEASE_MINOR_VERSION 4
#define POWER_IP_CFG_DEFINES_AR_RELEASE_REVISION_VERSION 0
#define POWER_IP_CFG_DEFINES_SW_MAJOR_VERSION 1
#define POWER_IP_CFG_DEFINES_SW_MINOR_VERSION 0
#define POWER_IP_CFG_DEFINES_SW_PATCH_VERSION 0
/*==================================================================================================
* FILE VERSION CHECKS
==================================================================================================*/
#ifndef DISABLE_MCAL_INTERMODULE_ASR_CHECK
/* Check if Power_Ip_Cfg_Defines.h file and StandardTypes.h file are of the same Autosar version */
#if ((POWER_IP_CFG_DEFINES_AR_RELEASE_MAJOR_VERSION != STD_AR_RELEASE_MAJOR_VERSION) || \
(POWER_IP_CFG_DEFINES_AR_RELEASE_MINOR_VERSION != STD_AR_RELEASE_MINOR_VERSION))
#error "AutoSar Version Numbers of Power_Ip_Cfg_Defines.h and StandardTypes.h are different"
#endif
#endif
/*==================================================================================================
DEFINES AND MACROS
==================================================================================================*/
/**
* @brief Derivative used.
*/
#define POWER_IP_S32K144
#if (defined(POWER_IP_S32K148) || defined(POWER_IP_S32K146) || defined(POWER_IP_S32K144) || defined(POWER_IP_S32K142))
#define POWER_IP_HSRUN_SUPPORT STD_ON
#else
#define POWER_IP_HSRUN_SUPPORT STD_OFF
#endif
/**
* @brief Support for Low Power mode.
*/
#define MCU_ENTER_LOW_POWER_MODE (STD_ON)
/**
* @brief
*/
#define MCU_PERFORM_RESET_API (STD_ON)
/**
* @brief ISR Mcu_ResetAlternate_ISR is/isn't available (STD_ON/STD_OFF)
*/
#define POWER_IP_RESET_ALTERNATE_ISR_USED (STD_OFF)
/**
* @brief ISR Mcu_PMC_UnderOverVoltage_ISR is/isn't available (STD_ON/STD_OFF)
*/
#define POWER_IP_VOLTAGE_ERROR_ISR_USED (STD_OFF)
/**
* @brief Enable the usage of Non-Autosar Peripheral CMU.
*/
#define MCU_ENABLE_CMU_PERIPHERAL (STD_OFF)
/**
* @brief This parameter shall be set True, if the H/W does not have a PLL or the PLL circuitry is enabled after the power on without S/W intervention.
*/
#define POWER_IP_NO_PLL (STD_OFF)
/**
* @brief This define controls the availability of function Mcu_SleepOnExit
*/
#define POWER_IP_SLEEPONEXIT_SUPPORT (STD_ON)
/**
* @brief Low Voltage Detect Status and Control 1 Register support (PMC_LVDSC1).
*/
#define POWER_IP_PMC_LVDSC1_SUPPORT (STD_ON)
/**
* @brief Enable the usage of Non-Autosar API Mcu_GetPowerMode_State() for getting infos system platform configuration.
*/
#define POWER_IP_POWERMODE_STATE_API (STD_OFF)
/**
* @brief If this parameter is set to TRUE, the System Mode Controller (SMC) initialization has to be disabled in the MCU driver.
*/
#define POWER_MODE_CHANGE_NOTIFICATION (STD_OFF)
/**
* @brief Enable the usage of Non-Autosar API Power_Ip_SRAMRetentionConfig().
*/
#define POWER_IP_SRAM_RETEN_CONFIG_API (STD_OFF)
/**
* @brief If this parameter is set to TRUE, the Reset Control Module (RMC) initialization has to be disabled from the MCU driver.
*/
#define POWER_IP_DISABLE_RCM_INIT (STD_OFF)
/**
* @brief If this parameter is set to TRUE, the Power Management Controller (PMC) initialization has to be disabled from the MCU driver.
*/
#define POWER_IP_DISABLE_PMC_INIT (STD_OFF)
/**
* @brief If this parameter is set to TRUE, the System Mode Controller (SMC) initialization has to be disabled from the MCU driver.
*/
#define POWER_IP_DISABLE_SMC_INIT (STD_OFF)
/*==================================================================================================
ENUMS
==================================================================================================*/
/*==================================================================================================
STRUCTURES AND OTHER TYPEDEFS
==================================================================================================*/
#ifdef __cplusplus
}
#endif
#endif /* #ifndef POWER_IP_CFG_DEFINES_H */
/** @} */