EC600G/components/bootloader/Kconfig

# Copyright (C) 2018 RDA Technologies Limited and/or its affiliates("RDA").
# All rights reserved.
#
# This software is supplied "AS IS" without any warranties.
# RDA assumes no responsibility or liability for the use of the software,
# conveys no license or title under any patent, copyright, or mask work
# right to the product. RDA reserves the right to make changes in the
# software without notification.  RDA also make no representation or
# warranty that such application will be suitable for the specified use
# without further testing or modification.

menu "bootloader"

config BOOT_LOG_ENABLED
    bool "Enable log in bootloader"
    default y if KERNEL_HOST_TRACE
    default y if SOC_8811
    default y if SOC_8850
    default n
    help
        When host trace is enabled, log will be output through debughost.
        When diag trace is enabled, log will be output through diag uart.

        Usually, there are no reason to disable log through debughost.
        However, there are cases that diag uart is expected to be "silent"
        during bootloader.

config FDL_LOG_ENABLED
    bool "Enable log in fdl"
    default y if KERNEL_HOST_TRACE
    default y
    help
        When host trace is enabled, log will be output through debughost.
        When diag trace is enabled, log will be output through diag uart.
        When download is performed through diag uart, log will be disabled
        forcedly.

        Usually, there are no reason to disable log through debughost.
        However, there are cases that diag uart is expected to be "silent"
        during bootloader.

if SOC_8910
    config FDL_FLASH_SIGCHECK_BEFORE_WRITE
        bool "signature check before flash write"
        default n
        help
            When it is enabled, flash download will perform signature check
            before erase and write flash. When the new image is not valid,
            the existed content on flash won't be modified.

            Download will be slower when it is enabled and secure boot is
            enabled.

    config FDL1_IMAGE_START
        hex "FDL1 uimage SRAM start"
        default 0x8000c0
        help
            FDL1 uimage SRAM start (not the code start address).

    config FDL1_IMAGE_SIZE
        hex "FDL1 uimage SRAM size"
        default 0xff40
        help
            FDL1 sram size (including uimage header), including uimage header
            and non-romed sram

    config FDL2_IMAGE_START
        hex "FDL2 uimage SRAM start"
        default 0x810000
        help
            FDL2 uimage SRAM start (not the code start address).

    config FDL2_IMAGE_SIZE
        hex "FDL2 uimage SRAM size"
        default 0x30000
        help
            FDL2 sram size (including uimage header), including uimage header
            and non-romed sram

    config BOOT2_IMAGE_START
        hex "Bootloader stage2 SRAM start"
        default 0x810000
        help
            Bootloader stage2 SRAM start (not the code start address).
            Usually, it is the same as FDL2 to reuse SRAM.

    config BOOT2_IMAGE_SIZE
        hex "Bootloader stage2 SRAM size"
        default 0x30000
        help
            Bootloader stage2 sram size, including uimage header and
            non-romed sram. Usually, it is the same as FDL2 to reuse SRAM.

    config BOOT_SYS_STACK_SIZE
        hex "Boot/boot2/FDL1/FDL2 SYS stack size"
        default 0x1800
        help
            Boot/boot2/FDL1/FDL2 are running in SYS mode. This is the
            stack size. All modes share the same stack.

    config BOOT_IRQ_STACK_SIZE
        hex "Boot/boot2/FDL1/FDL2 SVC stack size"
        default 0x800
        help
            Boot/boot2/FDL1/FDL2 IRQ stack size. All modes share the same
            IRQ stack.

    config BOOT_BLUE_SCREEN_SIZE
        hex "Boot/boot2/FDL1/FDL2 blue screen stack size"
        default 0x800

    config BOOT_SMPL_ENABLE
        bool "enblae SMPL(Sudden Momentary Power Loss)"
        default n
        help
            Enable SMPL. If it occurs that battery is dropped below UVLO
            threshold, all supplies will be shutdown simultaneously.

    config BOOT_SMPL_THRESHOLD
        int "SMPL(Sudden Momentary Power Loss)"
        default 7
        help
            The SMPL programmable timer.If the timer has expired by the
            time system supply recovers the PMIC does not auto boot and
            remains in power down state. When the system supply recovers
            before the timer expired the PMIC will boot up automatically.
            SMPL timer threshold value is three bits: 0: 0.25s; 1: 0.5s;
            2: 0.75s; ... 7: 2s

    config BOOT_PB_7S_RESET_ENABLE
        bool "support pb 7s reset"
        default n

    config BOOT_UART1_PDL_ENABLE
        bool "enable uart1 download"
        default n
        help
            When enabled, bootloader will use PDL protocol to support
            download. The baud rate is fixed to 921600, and only Limited
            PDL commands are supported.

endif

config DUAL_BOOTLOADER_ENABLE
    bool "enable dual bootloader"
    depends on SOC_8811 || SOC_8850
    default n  #quectel update
    help
        When enabled, there will exist two copies of bootloader at the
        beginning of FLASH.

        8811 and 8850 should always enable dual bootloader.

if SOC_8850
    config BOOT_SYS_STACK_SIZE
        hex "Boot/boot2/FDL1/FDL2 SYS stack size"
        default 0x1800
        help
            Boot/boot2/FDL1/FDL2 are running in SYS mode. This is the
            stack size. All modes share the same stack.

    config BOOT_IRQ_STACK_SIZE
        hex "Boot/boot2/FDL1/FDL2 SVC stack size"
        default 0x800
        help
            Boot/boot2/FDL1/FDL2 IRQ stack size. All modes share the same
            IRQ stack.

    config BOOT_BLUE_SCREEN_SIZE
        hex "Boot/boot2/FDL1/FDL2 blue screen stack size"
        default 0x800

    config BOOT_PB_7S_RESET_ENABLE
        bool "support pb 7s reset"
        default n

    config BOOT_UART1_PDL_ENABLE
        bool "enable uart1 download"
        default n
        help
            When enabled, bootloader will use PDL protocol to support
            download. The baud rate is fixed to 921600, and only Limited
            PDL commands are supported.
endif

if SOC_8811
    config BOOT_MAIN_STACK_SIZE
        hex "bootloader/fdl main stack size"
        default 0x2000
        help
            Main stack size of bootloader and fdl.

    config BOOT_PROCESS_STACK_SIZE
        hex "bootloader/fdl process stack size"
        default 0x2000
        help
            Process stack size of bootloader and fdl.
endif

config BOOT_TIMER_IRQ_ENABLE
    bool "enable timer IRQ"
    default n
    help
        When enabled, interrupt will be enabled in bootloader, and timer
        IRQ will be enabled. It is only used to feed external watchdog.

if BOOT_TIMER_IRQ_ENABLE
    config BOOT_TIMER_PERIOD
    int "boot timer period (ms)"
    default 500
    help
        Bootloader timer period, in milliseconds.
endif

config FDL1_PACKET_MAX_LEN
    hex "Maximum FDL1 packet length"
    default 0x840
    help
        Maximum FDL1 packet length. It should match configuration in
        ResearchDownload.

config FDL_PACKET_MAX_LEN
    hex "Maximum FDL packet length"
    default 0x3000
    help
        Maximum FDL packet length. It should match configuration in
        ResearchDownload.

config NVBIN_FIXED_SIZE
    hex "NV bin fixed size"
    depends on SOC_8910 || SOC_8811 || SOC_8850
    default 0x20000 if SOC_8910
    default 0x28000 if SOC_8850
    default 0x14000 if SOC_8811
    help
        At nv backup, fixed size is needed for nv bin read and write.
        This size should be large enough to hold all fixed nv bin.

if SOC_8910
config FDL_UART_BAUD
    int "Baud rate of default FDL UART"
    default 921600 if SOC_8910

choice
    prompt "FDL default UART"
    default FDL_DEFAULT_UART2

    config FDL_DEFAULT_UART1
        bool "UART1"

    config FDL_DEFAULT_UART2
        bool "UART2"

    config FDL_DEFAULT_UART3
        bool "UART3"
endchoice

config FDL_DEFAULT_UART
    string
    default "DRV_NAME_UART1" if FDL_DEFAULT_UART1
    default "DRV_NAME_UART2" if FDL_DEFAULT_UART2
    default "DRV_NAME_UART3" if FDL_DEFAULT_UART3
    default ""

endif

config BOOT_UNITY_OUTPUT_UART
    bool "bootloader unity output to uart"
    default y
    help
        Send unity output to uart. When unselected, unity output will be
        mixed into log.

if BOOT_UNITY_OUTPUT_UART
choice
    prompt "bootloader unity unit test uart"
    default BOOT_UNITY_UART1

config BOOT_UNITY_UART1
    bool "UART1"
config BOOT_UNITY_UART2
    bool "UART2"
config BOOT_UNITY_UART3
    bool "UART3"
config BOOT_UNITY_UART4
    bool "UART4"
config BOOT_UNITY_UART5
    bool "UART5"
endchoice

config BOOT_UNITY_UART_NAME
    string
    default "DRV_NAME_UART1" if BOOT_UNITY_UART1
    default "DRV_NAME_UART2" if BOOT_UNITY_UART2
    default "DRV_NAME_UART3" if BOOT_UNITY_UART3
    default "DRV_NAME_UART4" if BOOT_UNITY_UART4
    default "DRV_NAME_UART5" if BOOT_UNITY_UART5
    default ""

config BOOT_UNITY_UART_BAUD
    int "unity unit test uart baud rate"
    default 115200
endif

endmenu