EC600G/components/hal/Kconfig

# Copyright (C) 2018 RDA Technologies Limited and/or its affiliates("RDA").
# All rights reserved.
#
# This software is supplied "AS IS" without any warranties.
# RDA assumes no responsibility or liability for the use of the software,
# conveys no license or title under any patent, copyright, or mask work
# right to the product. RDA reserves the right to make changes in the
# software without notification.  RDA also make no representation or
# warranty that such application will be suitable for the specified use
# without further testing or modification.

menu "HAL Configurations"

config NVM_VARIANTS
    string "NVM variants"
    default ""
    help
        For each target, multiple nvm variants are supported. For each nvm
        variant, a separated pac file will be created.

        NVM variant is just a name, and the definitions are located in
        another configuration file. For 8910, each nvm variant will
        configure modem bin path and nvm prj file.

config PARTINFO_JSON_PATH
    string "partition infomation json file path"
    default ""
    help
        Partition information is stored as a json file. This json file
        will be converted into binary file, and embedded into bootloader.

        There are no default value, each target should specify the
        partition information file.

config PINMUX_JSON_PATH
    string "pinfunc defination json file path"
    default ""

config PACKAGE_FILE_JSON_PATH
    string "package raw file config path"
    default "components/nvitem/8910/default/prepack/prepack.json" if SOC_8910
    default "components/nvitem/8811/default/prepack/prepack.json" if SOC_8811
    default "components/nvitem/8850/default/prepack/prepack.json" if SOC_8850

config PACKAGE_FILE_APPIMG_JSON_PATH
    string "package raw file config path for appimg example"
    default ""
    help
        default "components/nvitem/8910/default/prepack/prepack_appimg.json" if SOC_8910
        default "components/nvitem/8811/default/prepack/prepack_appimg.json" if SOC_8811
        default "components/nvitem/8850/default/prepack/prepack_appimg.json" if SOC_8850  #adjusted by quectel

config SUPPORT_IMS_DELTA_NV
    bool "ims delta nv enable"
    default n

config SUPPORT_INNER_DELTA_NV
    bool "inner delta nv enable"
    default y if SOC_8850
    default y if SOC_8910
    default n

config ENABLE_DEBUGHOST_EVENT
    bool "enable debughost event"
    default y if SOC_8910
    default y if SOC_8850
    default n

config PWRKEY_POWERUP
    bool "power key power up enable"
    default y

config WAKEUP_PIN_POWERUP
    bool "wakeup pin (psm_ext_int) power up enable"
    default n

config SHUTDOWN_NORMAL_POWER_OFF
    bool "shutdown normal power off"
    default n
    help
        This is a normal power off mode in pmic 2720,
        more power consupmtion than PSM mode.

config KEYPAD_CSV_PATH
    string "keypad defination csv file path"
    default "components/hal/include/8811/keypad_map_8811.csv" if SOC_8811
    default "components/hal/include/8910/keypad_map_8910.csv" if SOC_8910

config PWRKEY_TIE_GND
    bool "power key tied to GND"
    default y
    help
        When power key is tied to GND, this should be selected. In this
        case, PWRKEY_WAKEUP_PSM should be deselected. Otherwise, PSM sleep
        will be wakeup immediately.

config PWRKEY_WAKEUP_PSM
    bool "power key wakeup psm"
    depends on !PWRKEY_TIE_GND
    default n
    help
        When selected, power key will wakeup system from PSN sleep.

config CHARGER_POWERUP
    bool "charger powerup the chip"
    default y

if SOC_8850
    config MED_CODE_ENCRYPT
        bool "enable med encrypt code"
        default n
endif

if SOC_8811
    config MED_CODE_ENCRYPT
        bool "enable med encrypt code"
        default n

    config LV_SUPPORT
        bool "support dcdc lower vol set"
        default n
        help
            Whether LV is supported

    config PM2_IND_GPIO
        int "gpio to indicate pm2 sleep"
        default -1
        help
            It is a GPIO to indicate PM2 sleep. At PM2 sleep, the GPIO will
            output low, and the GPIO will output high at PM0. When it is
            connected with a LED, the LED can indicate PM2 sleep.

            When it is negative, this feature is disabled.

    config PM3_IND_GPIO
        int "gpio to indicate pm3 sleep"
        default -1
        help
            It is a GPIO to indicate PM3 sleep. At PM3 sleep, the GPIO will
            output low, and the GPIO will output high at PM0 or PM2. When it
            is connected with a LED, the LED can indicate PM3 sleep.

            When it is negative, this feature is disabled.
endif

if SOC_8910
    config PMIC_INTR_GPIO
        int "GPIO for PMIC interrupt"
        default 6

    config SLEEP32K_GPIO
        int "GPIO for sleep 32K wakeup"
        default 7

    config TST_H_GROUND
        bool "tst_h to the ground"
        default n

    config CP_LTE_NBIOT_SUPPORT
        bool "CP Support Nbiot"
        default n

    config GPIO4_FORCE_PULL_UP
        bool "gpio4 (for sim detect) force pull up"
        default n

    config CAMA_POWER_ON_INIT
        bool "open CAMA power when init"
        default n

    config CAMA_CLK_FOR_AUDIO
        bool "open camera clock for audio"
        default n

    config GPIO_X_USED_FOR_VBAT_RF
        int "GPIO x is used for Vbat_RF switch"
        default 8
        help
            Then set gpio used for Vbat_RF switch.

    config GPIO_USED_FOR_VBAT_RF_SWITCH
        bool "Whether GPIO x is used for Vbat_RF switch"
#Edit by quectel.Vbat_RF is no used.
#        default y
		default n
        help
            Then set gpio used for Vbat_RF switch.

endif

config TRUSTZONE_SUPPORT
        bool "trust zone support"
        default n
        help
            Support trust zone feature or not, if support the
            partition layout must have corresponding region.


if TRUSTZONE_SUPPORT
config TRUSTZONE_SML_TOS_DIR
    string "trust zone sml and tos bin file dir"
    default ""

endif

config SYS_WDT_TIMEOUT
    int "sys_wdt timeout"
    default 10000
    help
        sys_wdt will always be enabled to trigger blue screen on system hang.
        This is the watchdog timeout.

        The default strategy of watchdog feed is in low priority thread. So,
        this timeout should be relative large, not to hit by system busy.

config SYS_WDT_FEED_INTERVAL
    int "sys_wdt feed interval"
    default 5000
    help
        This is the interval to feed sys_wdt.

config UNITY_OUTPUT_UART
    bool "unity output to uart"
    default y
    help
        Send unity output to uart. When unselected, unity output will be
        mixed into log.

if UNITY_OUTPUT_UART
choice
    prompt "unity unit test uart"
    default UNITY_UART1

config UNITY_UART1
    bool "UART1"
config UNITY_UART2
    bool "UART2"
config UNITY_UART3
    bool "UART3"
config UNITY_UART4
    bool "UART4"
config UNITY_UART5
    bool "UART5"
endchoice

config UNITY_UART_NAME
    string
    default "DRV_NAME_UART1" if UNITY_UART1
    default "DRV_NAME_UART2" if UNITY_UART2
    default "DRV_NAME_UART3" if UNITY_UART3
    default "DRV_NAME_UART4" if UNITY_UART4
    default "DRV_NAME_UART5" if UNITY_UART5
    default ""

config UNITY_UART_BAUD
    int "unity unit test uart baud rate"
    default 115200
endif

if BT_SLEEPTIME_SYNC_WITH_AP
config AP_SLEEP_SYNC_WITH_BT_SLEEPTIME
    bool "ap must wakeup before bt sleeptime expire"
    default y
endif

#quectel update
config SYS_WDT_ENABLE
    bool "whether to enable sys_wdt"
    default y
    help
        sys_wdt is a mechanism to trigger blue screen when system is not
        responsibile. Typically, it is implemented by NMI interrupt or FIQ.

endmenu